AA100 100% Silicone High Performance Acetoxy Cure Sealant Ultra-Clear Black

Product Description

 

100% Silicone High Performance Acetoxy Cure Sealant HM-AA100
Items	C*a/T*b/S*c/O*d	Unit	Typical Value	Requirement	Test Std.	Eqv. Std.
Appearance		-	-	Fine, uniform paste without bubbles, crusts, gels	Test StQ/QY-00-T001d	-
Density		g/cm3	1.02	1.02±0.03	GB/T 13477.2	-
Tack free	Properties Uncured	min	10	≤10	GB/T 13477.5	ASTM D2377:2000
Hardness, Shore A	Properties Cured	-	25	25±3	GB/T 531.1	ISO 7619-1:2004
Tensile Strength	Properties Cured	MPa	2.4	≥2.0	GB/T 528	ISO 37:2005
Elongation at break	Properties Cured	%	500	≥500	GB/T 528	ISO 37:2005

These figures are only intended as a guide and should not be used in preparing specifications.

PRODUCT DESCRIPTION

AA100 is a 100% acetoxy silicone sealant belongs to a single-component, acid-curing sealant that cures quickly and exhibits excellent mechanical properties, good elasticity, and can be used under a wide range of temperatures. It absorbs moisture from the air to cure and provides good adhesion to general glass and aluminum alloys. It is suitable for sealing aquarium structures and industrial applications.
 

APPLICATIONS

Sealing of glass showcases and display cabinets
Gap filling for aluminum alloy doors and windows. 
Sealing and bonding of glass, tiles etc.
Other general purpose filling or, waterproof sealing.

USAGE

It cannot be used for structural assembly
Do not use on surfaces where plasticizers or solvents may leak out, as this may cause damage to the sealant
It is not recommended to use it in a completely sealed space, which will cause it to not be able to cure completely due to lack of moisture
It is not recommended to use it in places that have been immersed in water for a long time
It is not recommended for structural surfaces that will come into direct contact with food
It is not recommended to use it on medical devices.
 

CONSTRUCTION

1. Cleaning of substrate surface

(1) The purpose of surface treatment before bonding is to remove oil, dust, surface damage and loose natural oxide film on the surface of the base material during the production and transportation process, so as to roughen the surface of the base material and form a surface suitable for mechanism embedding. morphology, while improving surface chemical properties and improving durability under the influence of stress environmental factors.

(2) Cleaning solvents are usually isopropyl alcohol, methyl ethyl ketone, and xylene. The cleaning cloth should be white, clean, soft, non-linting cotton.

(3) Use the "double cloth wiping" method to clean the surface of the substrate. Soak a clean cloth with solvent. Wipe the surface of the substrate in only one direction. Before the solvent evaporates, immediately use a second cloth with a clean dry surface. Wipe the solvent off the surface of the substrate.

(4) Do not put the soaking rag into the container for soaking, otherwise the clean solvent will be contaminated and the cleaning effect will be affected.

(5) Only clean the bonding and sealing construction part within 1 hour each time. Do not expose the cleaned substrate surface to the air for too long.

2. Make a bet
Use plastic tape to cover the surface near the interface to ensure that the sealing working lines are perfectly neat.
Cut the mouth of the hose, install the pointed tube, and then cut it at a 45° angle according to the size of the gap.
Install the sealant gun and press out the sealant along the gap at a 45° angle to ensure that the sealant is in close contact with the surface of the base material. When the joint width is greater than 15 mm, sealant needs to be applied multiple times. After gluing, trim the surface with a knife to remove excess sealant, then tear off the tape. If there are stains, use a damp cloth to remove them.

3. Pad material
Open-cell polyurethane or closed-cell polyethylene foam padding rods and polyethylene materials are recommended lining materials. Prevent sealant from sticking on three sides.

 

STORAGE & SHELF LIFE
Store the original sealant in a dry place, the temperature should not be higher than 27 degrees, the storage period is 12 months from the date of production.
 

PACKAGE

Standard 300ml plastic plastic bottle packing, 24 pcs/ctn; 500ml flexible film packing, 20 pcs/ctn;200L iron drum.
Store the original sealant in a dry place, the temperature should not be higher than 27 degreesCelsius, from the date of production, the storage period of 12 months.

 

Company Profile

Nanjing Howell New Materials Technology Co., Ltd.
Room 501, Unit 7, Xingzhihui, Xinghuo Rd 19th, Jiangbei New District, Nanjing, (211899), Jiangsu, China.

American Warehouse:Add: 1006 CROCKER RD, DOOR E5, WESTLAKE, OH 44145